logo
Good price  online

products details

Home > Products >
Anodizing Line Equipment
>
Automatic Compensation AC Power Filter Harmonic Filter with Over Current Protection for High Power Factor Anodizing Line Equipment

Automatic Compensation AC Power Filter Harmonic Filter with Over Current Protection for High Power Factor Anodizing Line Equipment

Brand Name: MEI-ALU
MOQ: 1set
Price: Negotiable
Packaging Details: Export Stander Packing
Payment Terms: T/T
Detail Information
Place of Origin:
CHINA
Current:
50Hz,380V
Name:
Anodizing Line Equipment
Supply Ability:
20pcs/month
Highlight:

AC Power Automatic Compensation Filter

,

AC Power Anodizing Line Equipment

,

Automatic Compensation Anodizing Line Equipment

Product Description
Product Overview

With the continued growth of modern industry, power electronics equipment has become widely deployed. The extensive use of non-linear loads — such as rectifier devices, smelting furnaces, intermediate-frequency furnaces, high-frequency furnaces, and single-crystal furnaces — introduces harmonic pollution into the power network. This degradation of power quality results in substantial energy waste and poses risks to the safety of electrical equipment. As a result, harmonic issues are receiving increasing attention from power departments.

In response to this challenge, our factory has developed and produced the AC Power Filter (also known as an LC Harmonic Processor). Using the principle of LC resonance, the filter monitors and analyzes harmonic sources, then introduces a series resonant branch into the power supply to absorb the contained harmonics before they can be injected into the grid.

This solution greatly improves the power factor of the grid and prevents abnormal equipment operation caused by grid harmonics. Under identical output parameters of the rectifier non-linear harmonic source, the filter can reduce the incoming line current from the grid by 20%–30%, saving electricity, lowering production costs, and improving the market competitiveness of the product.

This series features an advanced design principle, low cost, simple structure, high standardization, and an obvious harmonic absorption effect. It effectively filters high harmonics, reduces incoming current, and improves the power factor of the power grid.

Main Technical Parameters and Functions
  1. Designed primarily for three-phase four-wire power supplies: 50 Hz, 380 V.
  2. Special processing of 5N, 7N, 11N and other harmonics generated by the rectifier, with a harmonic filter rate of ≥ 80%.
  3. Under identical output current parameters of the original rectifier, the incoming line current from the grid decreases by 20%–30%.
  4. Equipped with over-current, over-voltage, under-voltage, and phase-loss protection systems.
  5. Raises the grid power factor of the rectifier to more than 0.90.
  6. Linkage with the oxidation power supply — no manual operation is required after startup. The filtering system starts automatically when the line current reaches a certain value.
Conditions of Use

This product is suitable for indoor use. Normal operating conditions are as follows:

  • Altitude shall not exceed 1,000 m. (For altitudes above 1,000 m, the use capacity shall be determined according to relevant regulations.)
  • Ambient temperature shall not exceed 50 °C.
  • Relative humidity of the air shall not exceed 85%.
  • The environment shall contain no explosive gas and essentially no corrosive medium.
  • Power supply: three-phase, 50 Hz, 380 V.
Installation and Operation
  1. The inductance of each reactor has been adjusted before the product leaves the factory. Therefore, no reactor screw may be removed — doing so may render the filter inoperative or, in serious cases, cause failure. Determine the service cross-sectional area of the cable according to the rated power of the oxidation power source, and pay attention to the grid connection end and the rectifier connection end on the filter.
  2. Connect the wiring terminal of the neutral line to a 2–4 mm² neutral line.
  3. After connecting each cable as described above, energize the unit and check whether the wind direction of the fan on top of the machine is correct. If the wind direction is downward, change the phase sequence of the fan input power supply.
  4. Turn on the working switch of the filter; the filter will automatically enter the working state without any further operation. As long as the oxidation rectifier is running, the filter will operate the corresponding filtering system. When the oxidation rectifier is turned off, the filter stops working.