600T/M Fully Automatic Horizontal Anodizing Production Line for 3C Components

This 600T/M aluminum anodizing production line is configured for the surface treatment of aluminum components used in 3C products, including aluminum parts for consumer electronics and related accessories.

The main surface treatment route focuses on anodizing and coloring. Depending on the required product finish, the process can be configured with pre-treatment, sulfuric acid anodizing, coloring, sealing and multiple rinsing stages. Aluminum anodizing creates a porous oxide layer on the aluminum surface, which can subsequently be colored through an appropriate dyeing or coloring process.

The horizontal layout is suitable for automated transfer between process tanks. A PLC-based control system can coordinate equipment movement and process sequences according to the configured production recipe.

For 600T/M production, the actual line capacity depends on factors such as workpiece dimensions, loading density, treatment area per rack, processing time, working hours and equipment utilization. These parameters should therefore be confirmed during line design rather than treated as a fixed output for every type of 3C component.

Final technical specifications, tank quantities, rectifier capacity, rack loading, treatment area and utility requirements should be confirmed according to the customer's aluminum parts and target production capacity.

• Horizontal Automatic Transfer: The horizontal configuration allows aluminum components to move between treatment tanks through an automated transfer system. This arrangement can be designed around the required process sequence and factory layout.
• Designed for 3C Aluminum Components: The line is intended for aluminum parts used in the 3C sector, where product dimensions, loading method, surface appearance and color requirements can vary considerably. Rack and fixture design can therefore be developed according to the actual component geometry.
• Anodizing and Coloring Process Integration: The production line combines anodizing with the subsequent coloring process within one automated production system. This allows the process sequence to be coordinated from pre-treatment through anodizing, coloring and sealing.
• Automatic Process Control: The automatic control system can manage equipment movement and process steps according to predefined process parameters. PLC and HMI-based control systems are commonly used for automated anodizing lines to coordinate transfer equipment and production sequences.
• Capacity Designed Around Actual Production Conditions: The 600T/M capacity is a line design target rather than a universal output for every component. Rack loading, aluminum surface area, processing time, working schedule and product geometry all affect actual production capacity.

A complete automatic aluminum anodizing line can include the following equipment sections:

• Automatic loading and unloading system
• Horizontal transfer equipment
• Degreasing tanks
• Rinsing tanks
• Etching / surface preparation tanks
• Neutralization or desmutting tank
• Anodizing tanks
• Anodizing rectifiers
• Coloring / dyeing tanks
• Coloring power supply or related equipment
• Sealing tanks
• Water circulation and rinsing system
• Heating and cooling equipment where required
• Process filtration and circulation equipment
• Automatic control cabinet
• PLC and HMI control system
• Aluminum racks and fixtures
• Exhaust and ventilation system
• Supporting water, air and utility systems

The final equipment configuration depends on the aluminum component size, alloy, surface condition, target color, anodizing requirements and production capacity.

This 600T/M horizontal anodizing production line can be considered for manufacturers producing colored aluminum components for:

• Consumer electronics
• 3C accessories
• Aluminum housings and covers
• Aluminum decorative components
• Small aluminum profiles and machined parts
• Electronic device components
• Other aluminum parts requiring anodizing and coloring

For 3C applications, the surface treatment process needs to be considered together with the upstream machining, polishing or surface preparation process. The final appearance can be affected by aluminum alloy, machining marks, surface preparation, anodizing conditions and coloring parameters.

What is a 600T/M aluminum anodizing production line?
A 600T/M aluminum anodizing production line is an industrial surface treatment system designed around a monthly production target of approximately 600 tons. The actual output depends on workpiece size, rack loading, treatment area, process cycle and operating conditions.

Is a horizontal anodizing line suitable for 3C aluminum components?
A horizontal anodizing line can be configured for 3C aluminum components, particularly when the production process requires automatic transfer between multiple treatment tanks. Rack design and process parameters should be developed according to the actual component geometry.

Can the 600T/M anodizing line be customized for different aluminum parts?
Yes. The line layout, tank configuration, rack design, transfer system, rectifier capacity and process sequence can be developed according to the aluminum part dimensions, production target, anodizing requirements and coloring process.

What information is needed to design a 600T/M automatic anodizing line?
The key information includes aluminum alloy, component dimensions, weight, surface area, required film thickness, target colors, monthly production, working hours, rack loading method and available factory utilities. These details are used to determine the process tanks, equipment capacity and line layout.